Autor Tema: Atomizer o-ring size  (Pročitano 3515 puta)

Van mreže bobpp

  • Global Moderator
  • Hero Member
  • *****
  • Thank You
  • -Given: 5385
  • -Receive: 8405
  • Poruke: 3338
  • Ugled: +9231/-0
  • Pol: Muškarac
  • elektronske cigarete
Atomizer o-ring size
« poslato: Avgust 18, 2016, 16:50:33 »
  • Publish
  • Mozda nekom zatreba a ako naletim na jos nesto ubacicu.


    - Kafun 3.1, Lite, Lite Plus, V2
         Chimney top: 5 mm x 1.5 mm
         Tank sections: 18 mm x 1 mm
         Fill screw (if applicable): 2 mm x 1 mm


    - Rose v2
         Chimney: 7 mm x 1 mm
         Coil body top: 15 mm x 1 mm
         Coil body bottom: 18 mm x 1 mm
         Tank sections: 18 mm x 1 mm
         Air control ring: 18 mm x 1 mm
         Brass 510 screw: 2 mm x 1 mm


    - Heron V1.5
         Deck: 18 mm x 1.0 mm
         Chimney: 18 mm x 1.5 mm
         13 mm x 1.5 mm


    - Kayfun V4
         17 mm x 1.5 mm     (x1)
         17 mm x 1 mm        (x3)
         13 mm x 1 mm       (x1)
         11 mm x 1.5 mm    (x1)
         10 mm x 1.5 mm    (x1)
         19 mm x 1.5 mm    (x2)
         5 mm x 1.5 mm      (x1)
         6 mm x 1.5 mm     (x2)




    - Kayfun mini V3
         10 mm x1 mm   (x2)
         9 mm x1 mm     (x2)
         10 mm x1.5 mm (x1)
         9 mm x1.2 mm   (x2)
         11 mm x1.1 mm (x2)
         8 mm x1.5 mm   (x1)
         18 mm x1.5 mm (x2)


    - Kayfun 2.1 mini
         Chimney top: 5 mm x 1.5 mm
         Tank Sections: 10 mm x 1 mm


    - Taifun GT
         17 mm x 1.5 mm - at each place where the end of the tank seals
         12 mm x 1 mm - on the chamber cap
         11 mm x 1 mm or 12 mm x 1 mm - under the sliding sleeve (11 mm x 1 mm on most, 12 mm x 1 mm on some)
         4 mm x 1 mm - on the end of the chimney (fill line)
         2 mm x 1 mm - under the 510 screw's head
         5 mm x 1.5 mm - on the drip tip


    - Taifun GS (mini)
         Top Cap/Tank Top + Tank Bottom: 12 mm x 1 mm
         Chimney Tube: 4 mm x 1 mm
         Base Top: 12 mm x 1 mm
         Chamber Cap 8 mm x 1 mm
         510 screw 2 mm x 1 mm
         Drip Tip 5 mm x 1.5 mm


    - Fogger 4.0
         Inside top cap (top of glass tank): 17 mm x 2 mm
         Base (bottom of tank): 17 mm x 2 mm
         Top of chimney: 3 mm x 1 mm
         Bottom of chimney: 10 mm x 1 mm
         Fill screw: 2 mm x 1 mm


    - Aqua V1
         Top cap: 17 mm x 1 mm
         Chimney: 7 mm x 2 mm
         Base to tank: 13 mm x 2 mm
         Inside base on big insulator: 13 mm x 2 mm
         On positive pin inside large insulator: 2 mm x 1 mm (3)


    - Kayfun V5
         7 mm x 1.5 mm   (x1)
         10 mm x 1 mm    (x2)
         11 mm x 1 mm    (x2)
         18 mm x 1.5 mm (x2)
         5 mm x 1.5 mm   (x1)
         6 mm x 1.5 mm   (x2)


    - Kraken
         Air Control: 11 mm x 1 mm
         Top cap: 12 mm x 1.5 mm
         Tank: 13 mm x 1.5 mm


    - Horizon Arctic
         Drip Tip: 5 mm x 1 mm   (x3)
         Atomizer: 13 mm x 1 mm
         Tank/Glass: 18 mm x 1.5 mm   (x2)
         Tank/Inner: 5mm x 1 mm
         Coil ( DIY ): 8 mm x 1 mm


    - Zenith V2
         18 mm x 1 mm


    - IGO-L, IGO-W (W2, W3, W4), IGO-T
         Top cap: 16 mm x 1 mm


    - Helios (clone)
         10 mm x 1 mm


    - Quasar RBA
         14 mm x 1 mm
         15 mm x 1 mm
         Top cap: 17 mm x 1 mm  (x2)


    - Manta v2 RDA
         19 mm x 1 mm


    - Griffin
         Top and bottom of glass: 19 mm x 1 mm  (x2 flat)
         Top of chimney: 15 mm x 1 mm  (x1)
         Bottom deck: 12 mm x 1mm  (x1)
         Drip tip/adapter: 9 mm x 1.5 mm  (x4)
         Between chimney halves: 10 mm x 1 mm  (x1)
         Centre top of chimney: 9 mm x 1 mm  (x1)

    - Taifun GT-T V2
         19 mm x 1 mm   (x2)
         3 mm x 1 mm   (x1)


    « Poslednja izmena: Septembar 01, 2016, 13:43:38 bobpp »

    Van mreže bobpp

    • Global Moderator
    • Hero Member
    • *****
    • Thank You
    • -Given: 5385
    • -Receive: 8405
    • Poruke: 3338
    • Ugled: +9231/-0
    • Pol: Muškarac
    • elektronske cigarete
    Odg: Atomizer o-ring size
    « Odgovor #1 poslato: Avgust 30, 2016, 17:35:20 »
  • Publish
  • Joyetech Cubis



    Dome RBA

    « Poslednja izmena: Septembar 26, 2016, 02:46:35 bobpp »

    Van mreže bobpp

    • Global Moderator
    • Hero Member
    • *****
    • Thank You
    • -Given: 5385
    • -Receive: 8405
    • Poruke: 3338
    • Ugled: +9231/-0
    • Pol: Muškarac
    • elektronske cigarete
    Odg: Atomizer o-ring size
    « Odgovor #2 poslato: Mart 21, 2017, 12:46:37 »
  • Publish
  • Phenomenon – Gus

    2 x    14mm x 1mm for the base
    2 x    19mm x 1mm for the top sleeve
    1 x    9mm x 1mm for the chimney

    Phenomenon ZEST V2

    20mm(inner diameter is 18mm);
    18mm(inner diameter is 16mm);
    10mm(inner diameter is 8mm);
    7mm(inner diameter is 5mm);
     
    GG Tilemahos V1 (ID x CS,mm)

    1 x   Center Post    3.5 x 2 (or 4 x 2) mm
    1 x   Top Cap          9 x 3 mm
    1 x   Rebuildable Part           14 x 1 mm
    1 x   Base        14 x 1 mm
    2 x   Center Post (AD Version)           3 x 1 mm
    2 x   AD Ring (AD Version)         18 x 1.5 mm


    GG Tilemahos V2 (ID x CS,mm)
     
    3 x   Center Post         3 x 1 mm
    1 x   Center Post Extension        5 x 2 mm
    1 x   Top Cap        10 x 3 mm
    1 x   Base       14 x 1 mm
    2 x   Base (AD Ring)         14 x 1 mm



    GG Tilemahos V2 plus (ID x CS,mm)

    3 x    Center Post        3 x 1 mm
    1 x    Center Post Extension      5 x 2 mm
    1 x   Top Cap      10 x 3 mm
    2 x   Base (AD Ring)       14 x 1 mm


     GG4S

        1x -  (17 x 1.5) Main brass body
        1x -  (1.78 x 1.78) Button center pin
        1x -  (16 x 1.5) Regular cap
        1x -  (15 x 1.5) AD cap's plastic
        1x -  (14 x 1) Around AD cap

    Esterigon


        2x  - (18 x 1.5) Air Flow Ring
        1x  - (10 x 1) Around Negative Battery insulator
        4x  - (8 x 1.5) 2 Around Center Post, 2 Around Positive Battery Pole
        1x  - (16 x 1) Around negative cap
        1x - (2 x 1) Button
        1x  – (4 x 2) Around locking cap post
        1x  - (4 x 1.5) (Additional O-ring Imeo has included for locking cap post)


    Just GG

        6 x 1 Around the axis top
        7 x 1.5 or 8 x 1.5 (2x) Around the Center Post of collector tank
        3 x 1.5 (2x) Around the Center Post of the 510 connection
        21 x 1.5 or 20 x 1.5 (2x) Inside the Air Control Ring
        14 x 1 Around the External threads of the Lid


    Ithaka's Telescopic Mouthpiece

        5 x 1 Around the external threads of the small upper section
        3 x 1.5 ((1) or (2)) On the neck of the polygonal internal body



    Ithaka

        9 x 2.5 Between Caps
        3 x 2 Under the Center Post
        21 x 1.5 Inside Control Ring
        14 x 1 On the Basic Feeding (not nessesary)
        16 x 1 (4x) Both sides of Clear Window, on the Base and on the Upper Body



    Penelope v4

        3 x 1 (3x) Around AD Center Pin
        3 x 2.5 Around Center Post Extension
        11 x 1 Around Base's threads
        9 x 3 Inside Refilling Cap



    Penelope v3

        10 x 1 (2x) Housing and Base
        9 x 3 Inside Refilling Cap
        3.5 x 2 Under the Center Post



    Penelope v2

        12 x 1.5 Base
        9 x 3 Inside Refilling Cap
        3 x 2 Under the Center Post
        5 x 1.5 (2x) Around the AD Mouthpiece Tip
        6 x 1.5 Spare O-Ring to eplace one of the 5x1.5, in case you want a more steady mouthpiece tip



    Penelope

        11 x 1.5 Base
        8 x 3 Top Cap
        1.78 x 1.78 Under the center post


    Odysseus

        16 x 1.5 (5x) Fat Odysseus base, between refilling cap and body, on the 2 sides of the clear window, GGTS Odysseus base
        1.78 x 1.78 Around the small slot in the base of the pin (UFS mode)
        3 x 1.78 Under center pin (all modes exept UFS mode)
        9 x 1.5 Inside 510 cone
        6 x 1.5 Top of the CE2 adapter
        11 x 1 Thin Odysseus base (dripping mode)
        9 x 2 Between caps

    Odysseus Short Mode

        16 x 1.5 (2x) Odysseus base, between refilling cap and body
        1.78 x 1.78 Under center pin
        9 x 2 Between caps

    Odysseus short mode (new rebuildable style)

        16 x 1.5 (2x) Odysseus base, between refilling cap and body
        1.78 x 1.78 Under center pin
        9 x 2 Between caps
        3 x 2 Under the center post's top nut


    Iatty

        13 x 1.5 Base of the connector
        3 x 1.78 (2x) Around ceramic
        4 x 2 Under mouthpiece


    GGTS

        2 x 1 (2x) Inside connector
        16 x 1.5 Between connector and CT
        21 x 1.5 Inside CR
        14 x 1 Outside of the lids
        9 x 1.5 Inside 901-510 lid
        11 x 1.5 Inside 801 lid


    UFS

        9x1.5 (2x) connector
        2x1 (2x) inside connector
        16x1.5 (2x) lower sleeve, between connector and CT
        21x1.5 CR
        17x1.5 upper sleeve
        5x1.5 extension 510
        9x2 under mouthpiece
        14x1.5 base of UFS
        4x1.5 under the pin


    AVS

        8x2 base of 901 atomizer inside AVS
        9x2.5 between 2 caps of the AVS tank
        16x1.5 (2x) big refill cap and between collector tank and connector of GGTS
        14x1 outside of the lids
        21x1.5 inside CR
        2x1 (2x) inside connector
        9x1.5 901 lid
        11x1.5 801 lid
        5x1.5 510 atomizer extension


    AFS

        8x3 base of 901 atomizer inside AFS
        15x2.5 base of the tank where it meets the CR
        19x1.5 inside CR
        9x3 between 2 caps of the AFS tank
        16x1.5 big refill cap
        12x1.5 base of the connector
    « Poslednja izmena: Maj 06, 2017, 11:17:17 bobpp »

    Van mreže bobpp

    • Global Moderator
    • Hero Member
    • *****
    • Thank You
    • -Given: 5385
    • -Receive: 8405
    • Poruke: 3338
    • Ugled: +9231/-0
    • Pol: Muškarac
    • elektronske cigarete
    Odg: Atomizer o-ring size
    « Odgovor #3 poslato: Septembar 11, 2017, 01:24:00 »
  • Publish
  • Coppervape Hussar (a verovatno i original)

    20*18*1
    17*15*1
    8*5*1.5
    4*2*1

    Van mreže bobpp

    • Global Moderator
    • Hero Member
    • *****
    • Thank You
    • -Given: 5385
    • -Receive: 8405
    • Poruke: 3338
    • Ugled: +9231/-0
    • Pol: Muškarac
    • elektronske cigarete
    Odg: Atomizer o-ring size
    « Odgovor #4 poslato: Novembar 26, 2017, 22:19:13 »
  • Publish
  • Kayfun Prime


    Van mreže kinkel

    • eCiginfo prijatelj
    • Hero Member
    • *****
    • Thank You
    • -Given: 1046
    • -Receive: 1056
    • Poruke: 592
    • Ugled: +1056/-0
    • elektronske cigarete
    Odg: Atomizer o-ring size
    « Odgovor #5 poslato: Novembar 27, 2017, 09:58:36 »
  • Publish
  • Evo sta sam nasao na nekom forumu sa SKU-ovima za FT .. za KF Prime
    5. O-ring - 7x1.5 - SKU 4624910
    8. O-ring 10x1 - SKU 2066605 ili SKU 4616907
    10. O-ring 11x1 - SKU 1536603 ili SKU 2066605
    11. O-ring 7x1.5 - SKU 4624910
    17. O-ring 18x1.5 - SKU 4624901
    19. O-ring 18x1.5 - SKU 4624901
    21. O-ring 5x1.5 - SKU 2071201 ili SKU 1536600
    22. O-ring 11x1 -  SKU 1536603 ili SKU 2066605
    24. O-ring 6x1.5 - SKU 4625001
    25. O-ring 6x1.5 - SKU 4625001

    Van mreže bobpp

    • Global Moderator
    • Hero Member
    • *****
    • Thank You
    • -Given: 5385
    • -Receive: 8405
    • Poruke: 3338
    • Ugled: +9231/-0
    • Pol: Muškarac
    • elektronske cigarete
    Odg: Atomizer o-ring size
    « Odgovor #6 poslato: Maj 25, 2020, 14:09:55 »
  • Publish
  • Tripod RTA

    18 x 1
    12.5 x 1.5
    2 x 1 (4)
    6 x 1.5
    16 x 1
    14 x 1 (2)
    Custom "L" shape (2)
    Custom flat


    Dvarw MTL RTA


    18×1 3 pcs
    6×1 1pc
    11×1 1pc
    6×1 1pc

    Dvarw DL RTA

    Batches 1-6:

    20×1 3pcs
    18×1 1pc
    13×1 1pc
    8×1 1pc

     
    Batches 7-:

    20×1 3pcs
    17×1 1pc
    12×1 1pc
    8×1 1pc